Product description
The new powerful electronics for any RepRap!
Megatronics is based on many famous open-source products including: Arduino Mega, RAMPS, SD Ramps. Therefor this product is an already proven design. It combines all major features of these board into a single board solution for more reliable 3D-printing. This board will get you the most features for the best price!
Megatronics has a powerful Atmega2560 processor with 256 kB memory, running at 16Mhz. The board can be connected to a PC using a normal USB cable. It will register as FTDI FT232R device. The board is compatible with the Arduino Mega 2560 and will therefor be easily programmed from the Arduino IDE.
This is only the board. Stepper drivers are not included.
Major features
Atmega2560
Powerful Atmega2560 processor with 256 kB memory, running at 16Mhz
Thermo couple (2x)
On board support for connecting two thermo couples
SD Card
Autonomous printing from Micro SD card on board, also an external SD card is supported
LCD support
Hooking up a LCD is pretty easy. The Wiring is compatible with most LCD screens. We do not sell the required wiring yet, but you can use 6x2-wire cable.
Six MOSFETs
The board has 3 MOSFETs (3x 25A) to support extruders, 2 MOSFETs fior fans and 1 MOSFET (IRLS3034PBF) for the heated bed
Four thermistors
Four thermistors are supported.
Up to 6 stepper drivers
Compatible with RAMPS, 6 slots for stepper drivers (not included). Modularized to make replacement easy for damaged drivers. This board also support the new DRV8825 driver from Pololu http://www.pololu.com/catalog/product/2132.
Support for many peripherals
The board's functions can be easily extended with LCD, keypad etc. See the connectors section for more information
Other features
- USB 2.0 Full Speed compatible
- Auto reset can be disabled by removing a jumper
- The board can be powered from 12-24V
- The LCD contrast can be adjusted with a trimpot
- The 5V line is protected by a 500mA resettable fuse
- A piezo is included to allow the printer to give feedback with sound
- Each stepper driver slot has a breakout to connect external stepper drivers to the board.
- Four layer high quality PCB board
Board dimensions
Width: 109.5mm
Length: 90.5mm
Height: 18mm
Datasheet: Coming soon
Marlin firmware: See download section (service -> software downloads)
What's in the box?
This is a kit of the following items.
| Quantity | Stock | Product |
|---|---|---|
| 4x | Heatsink for pololu / stepstick stepper drivers | |
| 1x | Heater wire 18AWG/5A, black ( per meter ) | |
| 1x | Heater wire 18AWG/5A, red ( per meter ) | |
| 3x | 3-wire cable 24AWG, Red Black Yellow (1m) | |
| 2x | 2-wire 24AWG cable, Red Black (1m) | |
| 4x | DRV8825 Stepstick 1/32 microstep Stepper Motor Driver | |
| 1x | Megatronics v3.3 - Controller board ( Arduino-compatible ) | |
| 5x | NEMA17 Stepper motor / 1.8° step / connector / flat shaft / 5.0 kg.cm | |
| 5x | Connector cable for stepper motor / 100cm / 4 leads | |
| 3x | Mechanical endstop PCB v1.2 |
| 1 - 9: | excl 1,264.40 DKK incl 1,580.50 DKK |
| 10 - 29: | excl 1,201.20 DKK incl 1,501.50 DKK |
| 30 - : | excl 1,138 DKK incl 1,422.50 DKK |
| Need a larger quantity? Contact our Sales department. | |
Add-onsAdd-ons
Explore valuable add-ons that correspond with the Megatronics v3.3 - Cartesian kit. The components and accessories will enhance performance and guarantee improved efficiency. Select a device or part that will make all the difference!
AlternativesAlternatives
Looking for a comparable product to the Megatronics v3.3 - Cartesian kit? Explore our selection of similar alternatives in place so that you always have a variety of options for any project. Feel free to reach out to us for advice on the alternatives.
